Material: Hardener based on a pollutant-free vinyl ester/acrylic co-polymer, Color: colorless transparent, pH-value: 3.8, Consumption: 1200 to 2500 g/m² (depending on textile)
TecClay, lightweight, light brown
from 18,90 €
product: non-drying modelling clay, material: with binding agents (microwax among others), fillers (zinc stearate, magnesium and micro hollow globules among others) and dyes
Gedeo modeling clay
from 7,50 €
air-drying, has synthetic binders, does not crack as it dries, curing time is 4 to 5 days (can be shortened by use of a microwave over), after opening must be stored in moist cloth and enclosed in a tightly closed...
Fimo Professional modeling clay 8004
from 3,40 €
Baking time and temperature: 30 minutes at 110°C, Packaging: reclosable foil packaging, Weight: 85 grams
Latex Moulding Material
from 10,90 €
natural rubber-based air drying single component casting material (dispersion), pre-vulcanized with ammonia (0.3%), very soft (no Sh-A data available), extremely elastic, very low viscosity, cures to a translucent...
SikaBlock PUR modelling board M450
from 6,90 €
material: extremely fine pored polyurethane-based light moulding material, Density: 450 kg/m³
from 13,90 €
oven-curing modelling compound (15 min. at 130 °C), very pliable, very crack resistant
Acrystal Prima acrylic resin
from 25,90 €
material: two component water-based acrylic resin system, Range of application: for casting, laminating and coating, for interior as well as protected exterior spaces
Fimo modelling clay Soft 8020
from 2,40 €
Baking time and temperature: 30 minutes at 110°C, Packaging: film packaging, Weight: 57 grams
Rigid-PVC round rod, opaque, coloured
from 1,70 €
SikaBlock PUR rigid modelling foam M150
from 24,90 €
very fine pored polyurethane-based rigid foam for model making, light yellow or light green, density: 150 kg/m³; compressive strength: 1,6 MPa (ISO 604), modulus of elasticity: 65 MPa (ISO 178), linear coefficient...
Acrylic polish paste
from 9,30 €
wax-free, water soluble, with polishing solids especially suitable for plastics, used for polishing acrylics and polycarbonates
Original Sculpey, white
from 13,50 €
oven-curing modelling compound (15 min. at 130 °C), very pliable, very crack resistant, miscible
Wet silicon carbide sandpaper, anthracite
from 1,00 €
silicone carbide grit, solid resin bonding, water repelling latex backing paper, for manual wet sanding of metal (not stainless steel), plastic, varnish and putty
material: 2 component casting resin, End state: material is reddish and transparent when cured, Working life: 25 to 100 minutes, Density: (at room temperature) approx. 1.05 g/cm³
Mixing cups, polyethylene
from 6,90 €
polyethylene single-use mixing cups (HDPE), translucent, colourless, opening diameter: 82 mm (250 ml), 106 mm (600 ml), inner walls and bottom are smooth
Biothan/Biodur 1785/330 casting resin, hard
from 26,90 €
Material: two-component polyurethane casting resin, Colour: colourless transparent when cured, Shore hardness: soft (ca. Sh-A 40 - 70), Mixing ratio: resin to hardener ca. 1.5-2.5 to 1
Elastic surfacer (filler), white cream
from 5,90 €
ready-to-use filler for interior use, drying time is 2-3 hours
POM (Delrin) round rod
from 6,20 €
material: polyoxymethylene (Polyacetal)
TFC PU casting resin set
from 32,90 €
Material: 2-component casting resin, Shore hardness: D 75, Color: white/beige (component A) and beige (component B), Mixing ratio: 1:1 by weight
Formenbau pouring box frame, adjustable, set
from 20,90 €
Material: Aluminium, Aluminium folded sheet: 4 pieces, each 100 mm x 200 mm x 50 mm, Aluminium base plate: 1 piece at 200 mm x 200 mm
Epoxy casting resin, water clear, set
from 43,90 €
cold-curing, two-component casting resin consisting of bisphenol A-epichlorohydrin and epoxy hardener with polyoxyalkyleneamine, unfilled, hard, very low viscosity (very pourable), cured material is colourless and...
TFC silicone rubber type 3 heat resistant, set
from 27,90 €
Material: Silicone rubber, Shore hardness: A 33, Color: red, Mixing ratio: 1:1 by weight
th = 6 mm, rich in pigments, with pure beeswax, corresponds to European Safety Norm (Toy Safety) EN71 (see info), for colour sorting of each set see info
TFC Xyrarock ceramic casting powder, snow white
from 19,90 €
Material: Synthetic, plasticized gypsum-based casting compound, Color: snow white, Mixing ratio: 1:4 (water:casting powder) by weight, Mixing time at 23°C: 30–45 sec.
Finishing paper, black
from 0,90 €
silicon carbide grit, hide glue bonding, backing paper 110 g/m², for manual or machine dry sanding of metal (not stainless steel), plastic, varnish and putty
InDeClay, lightweight, light grey
from 23,90 €
material: non-drying modelling clay made from binding agents (microwax among others), fillers (zinc stearate, magnesium and micro hollow ...
Gedeo crystal resin, transparent, coloured
from 15,40 €
2-component epoxy resin casting material, transparent, colourless, waterproof and UV resistant, mixing ratio of resin to water is 2:1, curing time: 12 hours for the surface, 24 hours for the core, shelf life when...
Worbla's Transpa Art modelling sheets
from 5,00 €
Product description: thermoplastic polyester, Colour: colourless, transparent, Thickness: ca. 0,8 mm, Density: ca. 1000 g/m²
from 2,95 €
material: 150 g/m²
SikaBlock modelling/tooling board M1000
from 19,90 €
material: homogeneous polyurethane-based modelling material, Density: 1,000 kg/m³, Modus of elasticity: 1,800 MPa (ISO 178)
Gedeo resin plaster
from 10,60 €
extra hard, high-quality alpha plaster, synthetic resin bonded, bright white, fine grained, non-clumping, mixing ratio of powder to water is 3:1; setting time is 8 – 15 minutes, demoulding time is 30 minutes,...
view more articles
Sign Up and Get 5€ Off Your Next Purchase
Exclusive vouchers and sale
All the news about Modulor
This is Modulor
We Love Material
Whether for design, architecture, model making, DIY, artwork or stationery: over 30,000 articles that make the heart beat faster. For professionals. And aspiring professionals.
Inspiring & Unique
Abreast of all developments in the world of materials: At Modulor there are always new, first-class products waiting to be discovered. In all shapes and colours – and in many instances tailor-made.
A Tradition of Creative Expertise
Questions about materials? We provide personalized and competent advice. With over 25 years of experience our enthusiasm for materials continues unabated: +49 (0)30 690 360
PayPal, credit cards, direct debit – at Modulor paying is very simple. Pay after delivery? No problem: just select „Invoice“ as payment method.
We deliver with our logistics partner quickly and securely – upon inquiry, same day delivery is even available within the Berlin city limits.
Standard shipping is free within Germany for orders over €80.
A Berlin Original
All the products and even more ideas can be experienced in person at our Berlin-Kreuzberg store. Over two floors and more than 3,000 m².
Welcome to Modulor
WITH or WITHOUT VAT?
As a business customer, see net prices - or as an individual customer, see all prices including sales tax.
Business customer Price with sales tax
Private customer with VAT
You can change your choice at the top of the page at any time in the future.