Consegna puntuale entro Natale per gli ordini ricevuti fino al 18.12. (DE)

Scorri verso l'alto
Ricerca
      Categorie
      Prodotti
      Sto cercando i prodotti...
      La ricerca di »« non ha prodotto risultati.

      Materiale per modellazione

      Applicazione

      Gruppo colore

      Marchio

      Prezzo

      24 Articolo   /   71 Varianti
      Vista
      Classificazione: Rilevanza
      • Rilevanza
      • Topseller
      • Prezzo crescente
      • Prezzo decrescente
      • Alginat universal moulding material
        3 Varianti
        Alginat universal moulding material
        da 14,90 €
        Sostanza: materiale da impronta a base di alghe in polvere con particelle di silano (fibra di vetro) come riempitivo, Coerenza dopo l'indurimento: elastico, dimensionalmente e dimensionalmente stabile
      • TFC silicone rubber type 2-1 low-viscosity, set
        4 Varianti
        TFC silicone rubber type 2-1 low-viscosity, set
        da 24,90 €
        Material: Silicone rubber, Shore hardness: A 35, Color: yellow, Mixing ratio: 1:1 by weight
      • TFC silicone rubber type 1 low-viscosity, set
        4 Varianti
        TFC silicone rubber type 1 low-viscosity, set
        da 24,90 €
        Material: Silicone rubber, Shore hardness: A 20 , Color: mint green, Mixing ratio: 1:1 by weight
      • Resina per stampi/plasmare PUR U1404
        5 Varianti
        Resina per stampi/plasmare PUR U1404
        da 29,90 €
        material: 2 component casting resin, End state: material is reddish and transparent when cured, Working life: 25 to 100 minutes, Density: (at room temperature) approx. 1.05 g/cm³
      • TFC silicone rubber type 15 translucent set
        4 Varianti
        TFC silicone rubber type 15 translucent set
        da 25,90 €
        Material: Addition-curing 2 component silicone rubber, Shore hardness: A 32 , Color: colorless, Mixing ratio: 1:1 by weight
      • TFC silicone rubber type 16 crystal clear, set
        4 Varianti
        TFC silicone rubber type 16 crystal clear, set
        da 25,90 €
        Material: Addition-curing 2 component silicone rubber, Shore hardness: A 20, Color: colorless, Mixing ratio: 1:1 by weight
      • TFC silicone rubber type 3 heat resistant, set
        4 Varianti
        TFC silicone rubber type 3 heat resistant, set
        da 24,90 €
        Material: Silicone rubber, Shore hardness: A 33, Color: red, Mixing ratio: 1:1 by weight
      • Latte di latex
        3 Varianti
        Latte di latex
        da 9,90 €
        materiale da impronta monocomponente indurente all'aria (dispersione) a base di gomma naturale, pre-vulcanizzato con ammoniaca (0,3%), molto morbido (non è disponibile alcuna informazione Sh-A), estremamente...
      • Pasta di latex
        2 Varianti
        Pasta di latex
        da 16,90 €
        materiale da impronta monocomponente indurente all'aria (dispersione) a base di gomma naturale, pre-vulcanizzato con ammoniaca, medio-duro, molto elastico, altamente viscoso (spazzolabile e riempibile), materiale...
      • Nuovo
        Creative Company foldable casting mould sheets
        2 Varianti
        Creative Company foldable casting mould sheets
        da 7,50 €
      • TFC silicone rubber type 6 food safe, set
        4 Varianti
        TFC silicone rubber type 6 food safe, set
        da 39,90 €
        Material: Addition-curing 2 component silicone rubber, Shore hardness: A 22, Color: white (component A) and apricot (component B), Mixing ratio: 1:1 by weight
      • Nuovo
        Gedeo Silicone mould
         
        Gedeo Silicone mould
        da 16,10 €
      • Moulding set
         
        Moulding set
        da 31,40 €
      • TFC silicone rubber type 8 kneadable, soft set
        4 Varianti
        TFC silicone rubber type 8 kneadable, soft set
        da 22,90 €
        Material: Addition-curing kneading silicone, Shore hardness: A 25, Color: white, (component A) and green (component B), Mixing ratio: 1:1 by weight
      • Latex Gedeo
         
        Latex Gedeo
        da 19,50 €
        materiale da impronta monocomponente indurente all'aria, a base di gomma naturale, pastoso, estremamente elastico, applicazione in 4 strati, tempo di essiccazione 6 ore
      • Polvere di talco
         
        Polvere di talco
        da 2,20 €
        elegantemente
      • Air-cured mould making compound
         
        Air-cured mould making compound
        da 5,90 €
        Product description: very soft and exact mould making compound, Attributes: air-drying, Colour: skin colour (caucasian)
      • TFC silicone paint
        6 Varianti
        TFC silicone paint
        da 14,90 €
        Material: Highly pigmented special dye for dyeing silicone rubber, Colors: black, white, blue, yellow, green, red, brown
      • TFC silicone rubber type 5 kneadable, set
        4 Varianti
        TFC silicone rubber type 5 kneadable, set
        da 29,90 €
        Material: Addition-curing kneading silicone, Shore hardness: A 40, Color: white (component A) and red (component B), Mixing ratio: 1:1 by weight
      • TFC silicone rubber type 12 durable, set
        4 Varianti
        TFC silicone rubber type 12 durable, set
        da 34,90 €
        Material: Addition-curing 2 component silicone rubber, Shore hardness: A 30, Color: white, Mixing ratio: 1:1 by weight
      • TFC thixotropic agent silicone rubber additive
        2 Varianti
        TFC thixotropic agent silicone rubber additive
        da 14,90 €
        Material: Thixotropic agent for thickening addition-curing silicone, Color: translucent, Mixing ratio: 1% up to a maximum 3% of the weight of the silicone, Mixing time: 60 sec. (Silicone component with thixotropic agent) and 60 sec. (Mixing of the silicone components)
      • TFC quarz powder silicon oxide silicon rubber additive
        2 Varianti
        TFC quarz powder silicon oxide silicon rubber additive
        da 11,90 €
        Material: Quartz powder (silicon oxide), Color: light yellow, Mixing ratio: Up to max. 1:1 (quartz powder:silicon component)
      • Set per modellare Gedeo
        4 Varianti
        Set per modellare Gedeo
        da 22,50 €
        vari set per progetti di fusione e stampaggio
      • Silicone oil V50
         
        Silicone oil V50
        da 9,50 €
        Ingredients: polydimethylsiloxane, Color: transparent colorless, Viscosity at 25° C: low viscosity/thin-bodied, 50 mPa·s, Density at 25° C: 0.96 g/cm³
      Informazioni su Materiale per modellazione

      In order to reproduce objects – for example, sculptures, models, surface textures or body parts – a mould must be made from the so-called “master pattern”. Elastic materials are the most suitable for making these moulds. We have assembled a list of them under the heading “Moulding materials” which can be found under the category “Modelling, Moulding, Casting”. They are:

      • RTV 2 mould silicone rubber
      • elastic polyurethane resin
      • Latex milk
      • Alginate

      The following tables can provide you with an overview of the advantages and disadvantages of the various moulding materials.

       

      Comparison of elastic moulding materials


      Attributes Comp./Treatment

      RTV 2 mould silicone

      Elastic PUR resin

      Latex milk

      Alginate
      Number of components two two one one + water
      Time and effort required very little very little very much very very little
      Linear shrinkage very little very little very much very very little4)
      Curing
      • reaction of 2 components
      • no heat produced
      • reaction of 2 components
      • heat produced
      • through drying

      • through “gelling”

      Risk of inhibition yes no no no
      Shelf life of the components (minimum) 6 to 12 months 12 months 24 months no information
      Toxicological/hazard info as a rule, hazardous label NOT required2) as a rule, hazardous label required
      hazardous label NOT required

      hazardous label NOT required
      Price high medium low low
      Attributes when cured        
      self-releasing yes no no no
      Time before first use of the mould 1 day to 1 week approx. 4 days approx. 3 days approx. 20 minutes
      Heat resistance high as a rule low low very low
      UV resistance conditional low no no
      Service life of the mould medium to long1) long short very short

      Comments
             
      Special features
      • can also be used as casting material


      • PUR components are sensitive to moisture
      • can also be used as casting material

      • smells like ammonia



      • mould must be kept wet
      • only good for a few pourings
      Intended uses flexible and block moulds for all pouring materials flexible and block moulds for all pouring materials flexible moulds for non-aggressive pouring materials body casts without extensive quality demands

      All the information refers primarily to the materials on offer at Modulor.
      1) depending on the type of crosslink
      2) Some hardeners require a hazardous label
      3) at room temperature (annealing possible if applicable)
      4) As long as pouring takes place within 20 minutes of making the mould

       

      The listed materials can of course be used for other purposes – for example, silicone is used to make temperature resistant seals, elastic polyurethane to make foams and latex to make examination gloves.

      Then again, hard, elastic materials like plaster are often used to make casts of objects. As a rule, very intricate moulds must be made for this work (see also the entry “Undercuts” in the “Small Lexicon” in the chapter “Silicone”).

      Modulor uses cookies to provide you with the best experience on our website. By continuing to browse the site you are agreeing to our use of cookies.    More information
      Benvenuto su Modulor
      CON o SENZA IVA?
      Come cliente commerciale è possibile visualizzare i prezzi netti o come cliente privato tutti i prezzi al lordo di IVA.
      Cliente commerciale
      Prezzi al netto di IVA.
      Cliente privato
      Prezzi al lordo di IVA.