Selective bonding

Ruderer L530 bzw. Technicoll 8008, toluol-free, transparent, colourless

contains solvent, transparent, yellowish, waterproof, aging-resistant, rubs off of the skin

contains solvent, transparent, colourless, waterproof, fast drying, with separate fine injector

ethyl cyanoacrylate adhesive, sets colourlessly, begins adhering after 5 - 120 seconds

ethyl cyanoacrylate adhesive, sets colourlessly, begins adhering after 5 - 60 seconds

contains solvent, transparent, colourless, waterproof, aging-resistant

transparent, colourless, for precise and fine gluing with a hollow needle

ethyl cyanoacrylate adhesive, sets colourlessly, begins adhering after 2 - 60 seconds

two component epoxy resin adhesive, without fillers, viscous, transparent, working life: 3 - 4 minutes, mixing ratio 1:1, temperature resistant from -50 to +80 °C

contains solvent, transparent, colourless, waterproof, aging-resistant, non-drip

inductor (catalyst) for all commercial super glues, colourless

closed cell PE foam, adhesive: rubber-based, temperature resistant up to ca. 65 C°, on silicone paper, given dimensions: height x length x width

two component epoxy resin adhesive, amber colour, working life: up to 5 minutes, mixture ratios 1:1, temperature resistant from -50 bis +60 °C

double-sided self-adhesive paper segments with pull tabs, white, 17 x 12 mm, solvent free, acid-free, archival quality

polypropylene, graduation from 0.5 to 3 ml, l = 160 mm

double-sided adhesive strips, opaque, white, removable without any residue, holds up to 300 g/strip

cyanacrylate glue, thin fluid, colourless when dry, plastic storage box with safety fastener

11 mm diameter, hot melt EVA (ethylene-vinyl acetate) glue, transparent, normal strength, low drip tendency

two component epoxy resin adhesive, resin (binder) is translucent white (18 g), hardener is honey-coloured (15 g); working life: 90 minutes; maximum bond after 12 hour; variable mixing ratio, temperature resistant...

polymerization adhesive, transparent when cured, waterproof

ø 11 mm, ethylene vinyl acetate copolymer (EVA) based hot melt adhesive, translucent, very high strength

permanently ductile adhesive paste made from synthetic vulcanized rubber, block is covered on two sides with release paper (approx. 120 x 70 x 3 mm), light blue, for easy but reliable and removable affixing of light...

nitro resin based adhesive, white, contains solvent, temperature resistant from –30 to +80 °C

ethyl cyanoacrylate adhesive, sets colourlessly, begins adhering after approx. 25 - 100 seconds

double-sided adhesive strips, opaque, white, removable without any residue, holds up to 1000 g/strip

ø 11 mm, ethylene vinyl acetate copolymer (EVA) based hot melt adhesive, transparent, normal strength, low-drip

removable adhesive pads, 10 x 12 mm, white, for quick and clean affixing of lightweight objects

blue plastic housing with storage clip, electronically regulated, mechanical feeder, for use with ethylene vinyl acetate copolymer (EVA) based hot-melt sticks ø 11 mm up to 250 mm in length power supply: 100 -...

11 mm diameter, hot melt EVA (ethylene-vinyl acetate) glue, curing time about 2 minutes, package content: 2 yellow, 1 orange, 2 red, 2 blue, 1 green

permanently ductile, kneadable self adhering sealing mass made of polyisobutylene, block covered with release paper (approx. 80 x 50 x 40 mm), blue-grey, for use as an interior and exterior seal as well as for...

alkoxy cyanoacrylate adhesive, low viscosity, weak smelling, sets colourlessly, begins adhering after approx. 10 - 150 seconds